Macrodyne set and request commands enumeration.
Declaration Syntax| C# | Visual Basic | Visual C++ |
[SerializableAttribute] public enum DeviceCommand
<SerializableAttribute> _ Public Enumeration DeviceCommand
[SerializableAttribute] public enum class DeviceCommand
Members| Member | Description |
|---|---|
| SelectEvent1 |
Select Event 1.
|
| SelectEvent2 |
Select Event 2.
|
| SelectEvent3 |
Select Event 3.
|
| SelectEvent4 |
Select Event 4.
|
| SelectEvent5 |
Select Event 5.
|
| SelectEvent6 |
Select Event 6.
|
| SelectEvent7 |
Select Event 7.
|
| SelectEvent8 |
Select Event 8.
|
| SelectEvent9 |
Select Event 9.
|
| SelectEvent10 |
Select Event 10.
|
| SelectEvent11 |
Select Event 11.
|
| SelectEvent12 |
Select Event 12.
|
| SelectEvent13 |
Select Event 13.
|
| SelectEvent14 |
Select Event 14.
|
| SelectEvent15 |
Select Event 15.
|
| SelectEvent16 |
Select Event 16.
|
| EraseSelectedEvent |
Erase selected event.
|
| ForceEvent |
Force an event.
|
| SetOneSecondPreTriggerValue |
Set the 1 second table pre-trigger to the value in the word buffer.
|
| SetExtendedPreTriggerValue |
Set the extended table pre-trigger to the value in the word buffer.
|
| SetUnitID |
Set the unit ID (8 ASCII bytes) to the values in the 8 byte buffer (set using SendUnitIDData.
|
| StartOnlineData |
Start sending ON-LINE data down this port (the port the command was received on).
|
| StopOnlineData |
Stop sending ON-LINE data or reference data down this port.
|
| StartSendingReferencePort1 |
Start sending the reference down port1.
|
| StartSendingReferencePort2 |
Start sending the reference down port2.
|
| StopSendingReference |
Stop sending the reference down either port.
|
| EnableReferenceReception |
Enable the reference reception in any port.
|
| DisableReferenceReception |
Disable the reference reception in any port.
|
| RebootUnit |
Re-boot the PMU code from the EEPROM and re-start the unit.
|
| ResetUnitAndFlags |
Reset the unit and reset the flags.
|
| Set2CycleOutputRate |
Set the output rate to 2 cycles (i.e. 30 times/sec).
|
| Set5CycleOutputRate |
Set the output rate to 5 cycles (i.e. 12 times/sec).
|
| Set10CycleOutputRate |
Set the output rate to 10 cycles (i.e. 6 times/sec).
|
| Use5Phasors |
Set the PMU for 5 phasors.
|
| Use4Phasors |
Set the PMU for 4 phasors.
|
| Use3Phasors |
Set the PMU for 3 phasors.
|
| Use2Phasors |
Set the PMU for 2 phasors.
|
| Use1Phasor |
Set the PMU for 1 phasor.
|
| SetMScaleValue |
Set mscale to the value in the word buffer.
|
| EnableAllTriggers |
Enable all triggers.
|
| DisableAllTriggers |
Disable all triggers.
|
| SetVMinTrigger |
Set the VMIN trigger to the value in the word buffer.
|
| SetVMaxTrigger |
Set the VMAX trigger to the value in the word buffer.
|
| SetAngdTrigger |
Set the ANGD trigger to the value in the word buffer.
|
| SetFreqTrigger |
Set the FREQ trigger to the value in the word buffer.
|
| SetDfDtTrigger |
Set the DFDT trigger to the value in the word buffer.
|
| SetLncmTrigger |
Set the LNCM trigger to the value in the word buffer.
|
| SetVCoefValue |
Set the VCOEF value to the value in the word buffer.
|
| SetFCoefValue |
Set the FCOEF value to the value in the word buffer.
|
| SetDCoefValue |
Set the DCOEF value to the value in the word buffer.
|
| SetNrmDigState |
Set the NRM_DIG (normal state of digital channel) to the value in the word buffer.
|
| SetDigEnbTrigger |
Set the DIG_ENB (digital channel trigger enable) to the value in the word buffer.
|
| ResetOnlineDataFormat |
Reset the ON-LINE data format to the default setting.
|
| AddSecondStatus |
Add the second status byte to the ON-LINE data.
|
| AddTimeStamp |
Add the time stamp to the ON-LINE data.
|
| AddSecondPhasor |
Add the second phasor to the ON-LINE data.
|
| AddThirdPhasor |
Add the third phasor to the ON-LINE data.
|
| AddForthPhasor |
Add the fourth phasor to the ON-LINE data.
|
| AddFifthPhasor |
Add the fifth phasor to the ON-LINE data.
|
| AddReferencePhasor |
Add the reference phasor to the ON-LINE data.
|
| SetVMinOperationalLimit |
Set the VMIN operational limit to the value in the byte buffer.
|
| SetVMaxOperationalLimit |
Set the VMAX operational limit to the value in the byte buffer.
|
| SetAngdOperationalLimit |
Set the ANGD operational limit to the value in the byte buffer.
|
| SetFreqOperationalLimit |
Set the FREQ operational limit to the value in the byte buffer.
|
| SetDfDtOperationalLimit |
Set the DFDT operational limit to the value in the byte buffer.
|
| SetLncmOperationalLimit |
Set the LNCM operational limit to the value in the byte buffer.
|
| SetDigitalOperationalLimit |
Set the digital channels operational limit to the value in the byte buffer.
|
| ResetOperationalLimitCounters |
Reset all operational limit counters (ANALOG AND DIGITAL) to 0.
|
| AddDigitals |
Add digital channels to the ON-LINE data.
|
| SetPhasorType |
Set the first set of analog channels to the value in the word buffer which designates what each channel will be, VOLTAGE or CURRENT.
|
| SetGpsTransparentMode |
Set GPS to transparent mode (host port A only).
|
| SendCommandToSecondBoard |
Send this command when the following command refers to the second board.
|
| SetDigitalsTo16 |
Set the number of Digital Channels to 16.
|
| SetDigitalsTo32 |
Set the number of Digital Channels to 32.
|
| SetRawPreTriggerValue |
Set Raw data pretrigger to the value in the word buffer.
|
| StartDebugMode |
Start Debug Mode. Stops PMU program and enters the debugger.
|
| RequestStatus1Flags |
Request STATU1 flag (1 response byte).
|
| RequestStatus2Flags |
Request STATU2 flag (1 response byte).
|
| RequestOnlineDataFormat |
Request ON-LINE data format (2 response bytes).
|
| RequestOperationalLimitFlags |
Request operational limit reached flags (3 response bytes).
|
| RequestWordBufferValue |
Request value in word buffer (2 response bytes).
|
| RequestByteBufferValue |
Request value in byte buffer (1 response byte).
|
| RequestTimeTagValue |
Request current time tag string (6 response bytes).
|
| RequestUnitStatus |
Request unit status.
|
| RequestAnalogTriggerValues |
Request analog trigger values (18 response bytes).
|
| RequestVMinTriggerValue |
Request VMIN trigger value (2 response bytes).
|
| RequestVMaxTriggerValue |
Request VMAX trigger value (2 response bytes).
|
| RequestAngdTriggerValue |
Request ANGD trigger value (2 response bytes).
|
| RequestFreqTriggerValue |
Request FREQ trigger value (2 response bytes).
|
| RequestDfDtTriggerValue |
Request DFDT trigger value (2 response bytes).
|
| RequestLncmTriggerValue |
Request LNCM trigger value (2 response bytes).
|
| RequestVCoefTriggerValue |
Request VCOEF trigger value (2 response bytes).
|
| RequestFCoefTriggerValue |
Request FCOEF trigger value (2 response bytes).
|
| RequestDCoefTriggerValue |
Request DCOEF trigger value (2 response bytes).
|
| RequestDigitalsNormalState |
Request normal state of digital channels (2 response bytes).
|
| RequestDigitalsTriggerEnabledState |
Request trigger enabled state of digital channels (1 response byte).
|
| RequestUnitIDBufferValue |
Request value in unit ID buffer (8 ASCII response bytes).
|
| RequestPhasorType |
Request the value which determines what each analog channel is, bit # = channel #, 1 = VOLTAGE, 0 = CURRENT.
|
| RequestOneSecondTableLine |
Request table line from 1 second table.
|
| RequestExtendedTableLine |
Request table line from extended table.
|
| RequestPreviousTableLine |
Request previous table line/block.
|
| RequestTableTimeInformation |
Request time information for selected table.
|
| RequestTableTriggerInformation |
Request trigger information for selected table.
|
| RequestTableWithFreezeReason |
Request table with freeze reason (16 response bytes).
|
| RequestTimeOfFreezeTableSize |
Request number of bytes in time of freeze tables (1 response byte).
|
| RequestTimeOfFreezeTables |
Request time of freeze tables.
|
| RequestOperationalLimitsValue |
Request value of operational limits (7 response bytes).
|
| RequestOperationalCountersValue |
Request value of operational counters (6 response bytes).
|
| RequestOperationalDigitalCountsValue |
Request value of operational counts of digital channels (16 response bytes).
|
| RequestRawTableLine |
Request raw table line.
|
| RequestRawTableInformation |
Request raw table information (18 response bytes).
|
| RequestCurrentRawTablePreTrigger |
Request current raw table pretrigger (22 response bytes).
|
| Undefined |
Undefined command.
|
Remarks
These commands should be transmitted in big-endian to make sure high word and low word are in the expected order.